#HANTEK 6022BE SOFTWARE ANDROID DRIVER#
#HANTEK 6022BE SOFTWARE ANDROID ANDROID#

HScope software by MartinLoren licenced through Google Play ВЈ9.99 (single trace version is free)

Nexus 7 phone (second generation) I have had since about 2014 mainly for Kindle duties.ДЎ50mm USB OTG adapter cable (in my box of strays and waifs) I have put STL files on Thingiverse along with STEP files so that the design can be modified for different displays. works better then just leaving them loose on the workbench. Havings said that, the stand for the scope probes, stylus etc. I wish that I had incorporated some cable stays on the frame as they get all over the place. An OTG connector will also be needed to connect the Micro-USB B connector to the main lead.Дownsides and things that havenвЂ™t worked too well: You have to disconnect the scope from both the powerbank and the tablet or it will drain them down вЂ“ there is no off switch. I have used a power bank which also reduces the chance of earth loops interfering with the signal. To get around this there is a second A-Type USB connector which can be connected to an external source of power.

#HANTEK 6022BE SOFTWARE ANDROID ANDROID#

The Hantek 6022BE can draw its power from the tablet or Android smartphone it is connected to but that can flatten the battery quickly. To have lost the last traces of the twiddly knobs that graced old scopes is sad, but only because I have an inner Luddite who also misses the crank handle, choke button and quarter lights on cars. It did take a wee while to get the hang of setting the sweep by calling up the number of samples per second and using the 'two fingered pinch' to get the horizontal display where I want it. Both probes and a stylus (to get around the fat finger problem) are held in a block separate from the scope/display which can be places wherever is convenient. The ergonomics of this layout is quite pleasing: The display can be tilted to a comfortable viewing angle and the oscilloscope is mounted on the same stand to give some weight.

#HANTEK 6022BE SOFTWARE ANDROID DRIVER#

Note: On Windows, you will have to assign the WinUSB driver via Zadig twice: the first time for the initial USB VID/PID the device has when attaching it via USB (04b4:6022 or 04b5:6022, depending on which vendor driver is currently being used by the device), and a second time after the firmware has been uploaded to the device and the device has 'renumerated' with a different VID/PID pair (1d50:608e).The Nexus 7 is a splendid small tablet with excellent resolution and works well but it was awkward to use lying flat on my workbench and, largely due to my fat fingers, it was hard to get the cursors to go where I wanted them to - there was a strong need for some kind of stand to hold the display. Note: The firmware is not flashed into the device permanently! You only need to make it available in the usual place where libsigrok looks for firmware files, it will be used automatically (and 'uploaded' to the Cypress FX2's SRAM every time you attach the device to a USB port). The firmware was originally written by Jochen Hoenicke (see README for details), thanks a lot! In order to use this device, the sigrok-firmware-fx2lafw (>= 0.1.4) firmware is required. Data format select = 'offset binary' (not 'twos complement').Д¬onnected to AD9288 ENC A and ENC B and FX2 IFCLK. NXP 74HC4051D (upper/lower, CH1/CH2) pinout:

4x 145 MHz FastFET Op Amp: Analog Devices AD8065 ( datasheet).

8-bit, 40/80/100MHz, dual ADC: Analog Devices AD9288 ( datasheet).

2W, fixed input, isolated & unregulated dual/single output DC/DC converter: Mornsun A_S-2WR2 (A0505S-2WR2) ( datasheet).

1A low-dropout voltage regulator (3.3V): Advanced Monolithic Systems AMS1117-3.3 ( datasheet).

2x 8-channel analog multiplexer/demultiplexer: NXP 74HC4051D ( datasheet).

256-byte Iв¬ EEPROM: Microchip 24LC02BI ( datasheet).

Hantek 6022be software android